公司新聞
冷再生機租賃工作中遇到輸送帶打滑問題該怎么辦？
來源：http://www.luhubox.com/ 日期：2020-08-24
冷再生機租賃進行施工階段，在連續使用過程中，不可避免地會有消耗和磨損。其中，銑床的輸送帶特別容易出現問題，運行時間長，可能出現打滑現象，影響工作效率。接下來，讓我們分析滑動的原因及其解決方案。
In the construction stage of leasing cold regenerator, in the continuous use process, there will inevitably be consumption and wear. Among them, the conveyor belt of milling machine is particularly prone to problems, long running time, may appear sliding phenomenon, affecting work efficiency. Next, let's analyze the causes of the slippage and the solutions.
1.初始張力太小。
1. The initial tension is too small.
輸送帶離開滾筒的地方張力不足會導致輸送帶打滑。一般來說，這種情況發生在啟動時，如果你想解決它，你需要調整張力裝置和增加初始張力。
Insufficient tension where the belt leaves the drum will cause the belt to slip. Generally speaking, this happens at startup, and if you want to solve it, you need to adjust the tension device and increase the initial tension.
2.摩擦不足
2. Insufficient friction
傳動滾筒和傳送帶之間的摩擦不足會導致打滑。造成這種現象的主要原因是輸送帶上有水或潮濕的環境。解決方法：在鼓中加入一些松香粉。小心不要用手放進去，要用爆破器材吹進去，以免發生意外。
Insufficient friction between the drive drum and the conveyor belt can cause slippage. The main reason for this phenomenon is that there is water or humid environment on the conveyor belt. Solution: add some rosin powder to the drum. Be careful not to put it in by hand, but to blow it in with blasting equipment to avoid accidents.
3.軸承損壞
3. The bearing is damaged
后滾筒軸承損壞不轉或上下滾筒軸承不轉。造成損壞的原因是機器尾部太浮、下沉，損壞或不靈活的部件沒有及時修理和更換，造成阻力增大、打滑。
The rear roller bearing does not rotate or the upper and lower roller bearing does not rotate. The cause of damage is that the tail of the machine is too floating and sinking, and the damaged or inflexible parts are not repaired and replaced in time, resulting in increased resistance and slipping.
4.啟動速度太快
4. The starting speed is too fast
如果起動速度太快，也可能發生打滑。此時可以緩慢啟動。如果采用鼠籠式電動機，啟動前可激活兩次，并能有效克服打滑現象。
If the starting speed is too fast, it may also slip. It can be started slowly at this time. If the squirrel cage motor is used, it can be activated twice before starting and can effectively overcome the phenomenon of slipping.
5.銑床租賃輸送帶超載
5. The conveyor belt of the milling machine is overloaded
如果輸送帶的負荷過大，超過電機的能力就會打滑。此時，打滑的好處是保護電機。否則，電機會在長時間后燒毀。但對于操作來說，這是一次滑倒事故。
If the belt is overloaded, it will slip if it exceeds the capacity of the motor. At this time, the advantage of slipping is to protect the motor. Otherwise, the motor will burn out after a long time. But for operation, it was a slip accident.
以上是關于冷再生機租賃工作中遇到輸送帶打滑問題的分析，希望對大家有所幫助，如您想要了解更多信息歡迎點擊http://www.luhubox.com。
The above is about the cold recycling machine rental work encountered in the conveyor belt slip problem analysis, hope to help you, if you want to know more information, welcome to click http://www.luhubox.com 。
公司地址：濟南市槐蔭區經一路273號群盛華城2號樓1-404
公司名稱：山東途暢路橋工程有限公司 
備案號：